Coats Kit 85009953, 28 Extended X-Clamps Manuel d'utilisateur télécharger pdf

28" Extended X-Clamps Kit #85009953

for Outside Clamping on Rim Clamp Tire Changers

(28” - 20", Outboard Position or 23" -18", Inboard Position)

COATS, Inc. • Hennessy Industries • 1601 J.P. Hennessy Drive, LaVergne, TN 37086-3565

(800) 688-6359 • (615) 641-7533 • (615) 641-5104 FAX • www.ammcoats.com

Installation

1. Unpack components.

2. Clean any debris from existing clamps, clamp carrier, and slides to

make replacement easier.

3. Remove the existing clamps by (refer to ﬁgure 1):

A. Depressing the large end of the spring loaded position button

with a ﬁnger through the large access hole on the side of the

clamp. At the same time depress the opposite end of the pin with

a small tool such as a valve core tool or small screwdriver through

the small access hole on the opposite side of the clamp.

B. Slide the clamp off the clamp carrier.

4. Clean and lubricate the clamp carriers and slides as instructed in

the maintenance section of the machine’s Operator Manual.

5. Install an Extended X-Clamp as follows (refer to ﬁgure 2):

A. Be sure the clamp is properly oriented on the table top—open

side of clamp jaw “V” toward center of table top.

B. Be sure the spring loaded position button is properly oriented in

the clamp carrier. If not, the clamp will be loose after installation.

C. Compress both sides of the spring loaded position pin and slide

the clamp onto the carrier and over the pin until it locks into posi-

tion.

6. Repeat step 5 for the remaining Extended X-Clamps.

7. Be sure all four Extended X-Clamps are in the same position

before attempting to secure a tire-wheel assembly.

Note: With clamp in outboard position the range is 28" - 20" or with

the clamp in inboard position range is 23" -18".

Usage

1. Depress the spring loaded position button with a ﬁnger, through

the large access hole in the side of the clamp. Slide the clamp to the

desired position for the wheel diameter about to be secured.

2. Be sure all four Extended X-Clamps are in the same position

before attempting to secure a tire-wheel assembly.

Note: With clamp in outboard position the range is 28" - 20" or with

the clamp in inboard position range is 23" - 18".

Figure 1 - Remove Existing Clamps.

Figure 2 - Install Extented X-Clamps.

Parts Identiﬁcation

Qty. Part No. Description

4 85009931 28" Grip Max Clamp

8 8182682 10-24 Nylock Nut

8 8301805 #10 Flat Washer

8 85000594 UHMW Grip

8 85000595 Laminated Clamp Cover

8 85000610 1/4 x 1-1/4 Shoulder Screw

4 8182250 Spring & Housing Assy Plunger

Installation 1
Parts Identiﬁcation 1

Résumé du contenu

Page 1 - Parts Identiﬁcation

Commentaires sur ces manuels

Pas de commentaire

Coats Kit 85009953, 28 Extended X-Clamps Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Coats Kit 85009953, 28 Extended X-Clamps. COATS Kit 85009953, 28 Extended X-Clamps User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Coats Kit 85009953, 28 Extended X-Clamps