1601 J. P. Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359 www.ammcoats.com Manual Part No.: 85008882 02HENNESSY INDUSTRI
4 • Important: Always read and follow the instructions.Operating the BalancerWheel MountingSelect the most appropriate mounting method for thewheel yo
Important: Always read and follow the instructions. • 5Standard Front Cone MountingA wheel should be centered by the outer side of thehub only when th
6 • Important: Always read and follow the instructions.Control Panel And Display1-2 Digital readouts, AMOUNT OF UNBALANCE,inside/outside3-4 Digital re
Important: Always read and follow the instructions. • 7Operation Functions MenuSee optimization unbalance sectiondiameterinch/mminch/mmwidthhoodstarta
8 • Important: Always read and follow the instructions.875 - Entering Wheel DimensionsFor clip-on weights, use gauge in the top position A.For adhesiv
Important: Always read and follow the instructions. • 9875 - t1-t2 and c1-t2 RimsSlide out the gauge on the LH side, at the pointwhere a weight is to
10 • Important: Always read and follow the instructions.775 - Manual Presetting Of WheelDimensionsStandard Wheels c1-c2/STATIC/t1-t3/c1-t3- Preset dis
775 - c1-t2 Wheel- Measure the dimensions as shown in the followingdiagramPresetting:nominalNote: when dt2 is not set, dt2 = d + 2" is automatic.
12 • Important: Always read and follow the instructions.Behind Spoke (Hidden Weight)The SPLIT function is used to position the adhesiveweights behind
Important: Always read and follow the instructions. • 13Match Mount- This function serves to reduce the amount of weightto be added in order to balanc
ii • Important: Always read and follow the instructions.
14 • Important: Always read and follow the instructions.Correction ModesFrom the measurement screen, press or button to select the type required. If
Important: Always read and follow the instructions. • 15875 - Manual DimensionPresetting (Use only in particularcases or for test)875- c1-c2/STATIC/t1
16 • Important: Always read and follow the instructions.875 - t1-t2 Rims- Setting:To go to these functions:- press one of the two buttons for more tha
Important: Always read and follow the instructions. • 17Self-CalibrationFor machine self-calibration proceed as follows:- Fit a wheel with steel rim o
18 • Important: Always read and follow the instructions.Maintenance InstructionsThe balancer requires only minor maintenance tokeep the unit operating
Important: Always read and follow the instructions. • 19Installation InstructionsA factory trained COATS®Service Technician mustperform the install,
20 • Important: Always read and follow the instructions.Floor and Space RequirementsThe balancer must be located on a flat floor of solidconstruction,
Important: Always read and follow the instructions. • 21Unpacking the Unit1. Remove the shipping carton from the pallet.2. Remove all loose parts and
85008882 02 03/08 © Copyright 2007 Hennessy Industries and COATS All Rights Reserved Printed in USA
Important: Always read and follow the instructions. • iiiTable of ContentsImportant Safety Instructions . . . . . . . . .iv - viOwner’s Responsibilit
iv • Important: Always read and follow the instructions.IMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONSREAD ALL INSTRUCTIONS1. Eye and face prote
Important: Always read and follow the instructions. • vOwner’s ResponsibilityTo maintain machine and user safety, the responsibil-ity of the owner is
vi • Important: Always read and follow the instructions.Safety Notices and DecalsFailure to follow danger, warning, and cau-tion instructions may lead
Important: Always read and follow the instructions. • 1Balancing Your First Tire1. Turn the machine OFF then ON(resets machine).Note: The machine wak
2 • Important: Always read and follow the instructions.Principle Operating PartsDo It Now!Now is a good timeto fill out the Owner’sRegistry Card.✓
Note: Throughout this manual wheel weights arereferred to as Clip-on or Tape-A-Weight™. Figure 3shows an example of each weight.Corrective Weight Exam
Commentaires sur ces manuels