Coats 1250 Series Balancer Manuel d'utilisateur

1601 J. P. Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359 www.ammcoats.com Manual Part No.: 8114307 13HENNESSY INDUSTRIE

4 • Important: Always read and follow the information box instructions.When prompted by balance r instructions, use the off-set arm (figure 6A) to

Important: Always read and follow the information box instructions. • 5Figure 7C - T2-Tape (Hidden Tape-A-Weight®) Data EntryDiagramUsing The Laser

6 • Important: Always read and follow the information box instructions.Laser Guided Operation™ SystemThe operator must select T2 - Tape Laser Locator

Important: Always read and follow the information box instructions. • 7Setting Wheel Dimensions (DIM)Before a wheel can be balanced, wheel dimensions

8 • Important: Always read and follow the information box instructions.(See Figure 14A or 14B)1 Weight Display Windows2 Mode Indicators3 Left Weight P

Important: Always read and follow the information box instructions. • 91223456789Figure 14A - 1250 Video Control Panel Feature Reference1223456789Fig

10 • Important: Always read and follow the information box instructions.Control Panel Quick ReferenceScreen Saver Mode (Video)By default, the 1250 vid

Important: Always read and follow the information box instructions. • 11Direct Select™ Weight Placement LocationBefore spinning the wheel, use direct

12 • Important: Always read and follow the information box instructions.Balancing Using Direct Select™A variety of wheel configurations can be balance

Begin by following the Laser Guided Operation™ pro-cedure, steps 1 through 4 on page 6.1. When unbalance is displayed, rotate wheel untilinboard cente

ii • Important: Always read and follow the information box instructions.IMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONSREAD ALL INSTRUCTIONS1. Ey

14 • Important: Always read and follow the information box instructions.Mounting Wheel on SpindleShaftAvoid back injury, seek assistance when lift-ing

Important: Always read and follow the information box instructions. • 15Standard Front Cone MountingA wheel should be centered by the outer side of t

16 • Important: Always read and follow the information box instructions.Match Balance (Optimization)The Match Balance (Tire/Rim Weight Optimization)pr

Important: Always read and follow the information box instructions. • 17CalibrationMachine CalibrationImportant: Be sure to use the correct calibrati

18 • Important: Always read and follow the information box instructions.3. Bring the tip edge of the arm precisely to the outeredge of the faceplate a

Important: Always read and follow the information box instructions. • 19Diagnostic ProceduresAfter Balance Vibration ProblemsIf vibration is still pr

20 • Important: Always read and follow the information box instructions.Installation InstructionsReceivingThe shipment should be thoroughly inspected

Important: Always read and follow the information box instructions. • 21SpecificationsWheel Diameter Range8 - 30 inchesWheel Width Range2 - 20 inche

8114307 13 6/13 © Copyright 2005 Hennessy Industries and COATS All Rights Reserved Printed in USA

Important: Always read and follow the information box instructions. • iiiOwner’ s ResponsibilityTo maintain machine and user safety, the responsibil-

iv • Important: Always read and follow the information box instructions.Safety Notices and DecalsFailure to follow danger, warning, and cau-tion instr

Important: Always read and follow the information box instructions. • vStandard Safety Devices• STOP key for stopping the wheel under emergencycondit

vi • Important: Always read and follow the information box instructions.Table of ContentsImportant Safety Instructions . . . . . . . . . . . . .iiOwne

Important: Always read and follow the information box instructions. • 1¨Balancing Your First Tire1. Turn the machine OFF then ON(resets machine).Note

2 • Important: Always read and follow the information box instructions.Principle Operating PartsABCDEFGHJKDo It Now!Now is a good time tofill out the

Important: Always read and follow the information box instructions. • 3Know Your UnitCompare this illustration with the unit before placingit into s