READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine for ease o
Operation Manual - COATS PRO GUARD PLUS - 105.0_REMEMBER R.I.M.Three Simple Steps To Help Keep Shops SafeR.I.M. is a training program developed by Hen
Operation Manual - COATS PRO GUARD PLUS - 116.0_PRINCIPLE OPERATING PARTSControl panelBead loosening discHelper ArmPedal controlsLiftInfl ationSpindle
Operation Manual - COATS PRO GUARD PLUS - 12NLMThe pedal control (L) is used to move the vertical arm out of the working position, once the tire has b
Operation Manual - COATS PRO GUARD PLUS - 137.1_Control Overview175121534678910111213141618192021221-Tower tilt pedal control2- Clockwise and counterc
Operation Manual - COATS PRO GUARD PLUS - 14Push the lever (23) down to be able to take the tool out of its seat and push it up to put it back in posi
Operation Manual - COATS PRO GUARD PLUS - 158.0_TRANSPORT- The tire changer is to be transported in its original packaging and kept in the position in
Operation Manual - COATS PRO GUARD PLUS - 1610.0_INSTALLATION10.1_Space required to position the machineWhen choosing the place of installation, remem
Operation Manual - COATS PRO GUARD PLUS - 1710.3_Commissioning- Connect the machine to the electrical mains, which must have line fuses and an effi cie
Operation Manual - COATS PRO GUARD PLUS - 18- Press pedal M and the lift P should raise; to lower the lift, lift the same pedal upwards.- Press pedal
Operation Manual - COATS PRO GUARD PLUS - 1912.0_IDENTIFYING AND CHECKING THE RIM AND TIREBefore you start to demount the tire, it is of CRUCIAL IMPOR
Operation Manual - COATS PRO GUARD PLUS - 2
Operation Manual - COATS PRO GUARD PLUS - 2013.0_POSITIONING THE VALVEFig. 6 shows a rim in the form of a clock, so that, following the various proces
Operation Manual - COATS PRO GUARD PLUS - 2115.0_TIRE LIFTA conventional rim is a wheel of a vehicle with rim made of steel or light aluminium, with a
Operation Manual - COATS PRO GUARD PLUS - 221. Insert the ring nut hub correctly (the cone plastic cover preserving the alloy rims from damages)2. T
Operation Manual - COATS PRO GUARD PLUS - 23Check the correct centering and locking of the wheel onto the center-plate. Check that the upper disk arm
Operation Manual - COATS PRO GUARD PLUS - 24Fase 3Keep the bead-loosening unit set up as for upper bead release: the lower roller is always aligned wi
Operation Manual - COATS PRO GUARD PLUS - 25The lower bead of reverse drop center rims with signifi cant width may be hard to break with the lower disk
Operation Manual - COATS PRO GUARD PLUS - 26Fig. 620- As soon as the bead is perfectly hooked, lift the mounting tool by raising lever ref. 20 to pull
Operation Manual - COATS PRO GUARD PLUS - 27- In order to help the bead coming out and reduce the stress to the tire:insert the plastic lever (as show
Operation Manual - COATS PRO GUARD PLUS - 2819.2 Upper bead mounting- Keep the mounting arm and the mount/demount head at working position, then put t
Operation Manual - COATS PRO GUARD PLUS - 2917- Press the button ref. 11 to lower the upper bead loosening roller until the upper bead reaches 3 cm le
Operation Manual - COATS PRO GUARD PLUS - 3INDEXINTRODUCTION...
Operation Manual - COATS PRO GUARD PLUS - 30Fig. 1Fig. 2Fig. 319.3 UHP (low profi le) and RUN-FLAT (self-supporting) tires mounting- Some precise and c
Operation Manual - COATS PRO GUARD PLUS - 3120.0_INFLATIONTires are to be infl ated with utmost caution. Strictly follow the instructions here after as
Operation Manual - COATS PRO GUARD PLUS - 32Supplied in the box21.1_Optional AccessoriesClamping adaptor for rims without center hole (P/N# 89231514)F
Operation Manual - COATS PRO GUARD PLUS - 33Turn the pins of the fl ange so that the center di-stance matches the measurement made earlier on the rim.T
Operation Manual - COATS PRO GUARD PLUS - 34LT TRUCK CONE KIT (P/N# 89231513) for clamping rims with center hole larger than Ø 7,5”-9.0” (190 -220 mm)
Operation Manual - COATS PRO GUARD PLUS - 35DROP CENTER TOOL (P/N # 89218904)Provides additional pressing point and extra help to assist arm, in kee-p
Operation Manual - COATS PRO GUARD PLUS - 36CLAMPING CONE BOOTIES KIT (P/N # 89231516)TABLE TOP PADS KIT (P/N # 89231517)ANTI-ROTATION PIN BOOTIES KI
Operation Manual - COATS PRO GUARD PLUS - 3722.0_RE-POSITIONINGTo re-position the tire changer in a new workplace, you need to secure the moving parts
Operation Manual - COATS PRO GUARD PLUS - 38Observe the instructions that follow to ensure the perfect operation and lasting life of your tire changer
Operation Manual - COATS PRO GUARD PLUS - 39Clean up the oil and send to special disposal centers according to current State and Federal regulations26
Operation Manual - COATS PRO GUARD PLUS - 420.0_Infl ation...
Operation Manual - COATS PRO GUARD PLUS - 4027.0_TECHNICAL SPECIFICATIONSSPECIFICATIONSElectrical RequirementsPower Supply Requirements 230V, 50/60
85606719 02 11/2013 © Copyright 1998 Hennessy Industries and COATS® All Rights Reserved. ONE WORD FOR SAFETYREAD INSPECT MOUNT BE CAREFUL OF THESE
Operation Manual - COATS PRO GUARD PLUS - 5INTRODUCTIONWe thank you for purchasing one of our tire changers, which are particularly suitable for mount
Operation Manual - COATS PRO GUARD PLUS - 61.0_GENERAL INFORMATIONThe tire changer is designed to demount and mount tires of passengers cars and light
Operation Manual - COATS PRO GUARD PLUS - 72.1_Safety InstructionsOwner’s ResponsibilityTo maintain machine and user safety, the responsibility of the
Operation Manual - COATS PRO GUARD PLUS - 83.0_SAFETY DEVICESThe tire changer is equipped with safety devices that are designed to guarantee the safet
Operation Manual - COATS PRO GUARD PLUS - 94.1_Safety Decals (p/n 82031373)
Commentaires sur ces manuels